Contact Us

         

123 Street Avenue, City Town, 99999

(123) 555-6789

email@address.com

 

You can set your address, phone number, email and site description in the settings tab.
Link to read me page with more information.

Blog

"Great use of science!"

Kevin Kelley

"Great use of science! Even though I have a large laundry room, I have to pull the dryer out 3’ to get behind and hook up the vent. Then I had to climb over the dryer. With MagVent there's no more climbing! And the dryer is inches away from the back wall. (The reason it’s hard to see the installation in the “after” picture.)"

-William M.

Read More

I Tell Everyone About MagVent...

Kevin Kelley

“I've moved, re-moved, and finally stacked my stupid dryer sooo many times over the years. Thankfully my vent hole was measured exactly, and lines up well - but still needed a somewhat "unconventional" multi-layered vent run, baled together with some electrical wire, to be able to push it in straight without crushing the metal.”

Read More

Compelled by MagVent...

Kevin Kelley

"Compelled to say, after installing a new dryer using your venting solution - VERY happy with your product (and the lovely person that I spoke to on the telephone). Massive improvement over my previous mess of venting - nice short straight shot outside! Thank you for your inventiveness."

-Rand R.

Read More

MagVent FAQ

Kevin Kelley

Will a MagVent coupling fit my dryer?

All MagVent couplings are designed to fit the standard 4 inch dryer vent. Which model you need for your installation needs depends on how far your dryer vent is from your exit vent when measuring from center to center of the vents.

Which MagVent coupling is best for my installation needs?

We offer three different MagVent models to fit a variety of venting needs. The MagVent MV-180 is designed for when the dryer vent is aligned with the wall vent in a straight 180 degree line, and offset by not more than 3 inches when measuring from center to center of the vents. If the vent path takes a 90 degree turn up the wall or down through the floor, or if it is off to the side at least 9 inches, then you need the MagVent MV-90. When using the MV-180 or the MV-90, keep in mind that for every inch of offset in vent alignment it requires an extra inch of clearance behind the dryer to accommodate the slight bend in the self-aligning transition hose. If the exit vent is between 3 inches and 9 inches away from the dryer vent, then you need the MagVent MV-Flex. The MV-Flex is not a self-aligning model like the other two, but it does give you more leeway with your vent alignment. With the MV-Flex you provide your own length of hose and manually align the magnets. The MV-Flex allows you to use the shortest piece of hose possible to make the connection once your dryer is in place, eliminating the typical, extra long hose that gets crushed and obstructed behind the dryer.

If you would like help determining which MagVent model is right for your installation needs, you are welcome to send inquiries to info@magventllc.com. Please describe how your vents align and how far apart they are when measuring from center to center of the vents, or include photos of your vent alignment.

Read More

Highly Recommended

Kevin Kelley

“The MagVent dryer vent is a terrific product that is ideal for making a dryer vent connection with limited space. The magnetic mount allows for a secure/tight connection and is super easy to install. I am super satisfied with this product and I highly recommend it.” Christopher H.

Read More

"Thank You For The Great Product!"

Kevin Kelley

“When we first purchased our home, the dryer was hooked up using a flimsy foil duct as you can see in the before photo. I saw an ad for MagVent online and ordered the MagVent MV-90 kit the next day. This is a much cleaner installation and will not trap lint like the foil duct had. The magnetic coupling is also helpful, especially with the tight closet where the washer and dryer are located. Thank you for a great product!” - Eric N.

Read More

Lower Profile, Easier Access...

Kevin Kelley

"I had the retailer install the new dryer I purchased. The first three pictures are what I ended up with. After finding your product, I installed the new MagVent MV-180. The last three pictures show the end result. My dryer is closer to the wall, and if I have to do any work behind the dryer, it makes it a lot easier.

I am so glad I found this product."

Van O.

Read More

MagVent Preferred to Old Fashioned Venting Method

Kevin Kelley

“I installed a MagVent MV-90 recently, and prefer it to the old machine-to-flex-pipe-to-wall method of venting a dryer. I can now push the two machines closer together and pull the dryer away from the wall without worrying about damaging the vent connection.” -Nick D.

Read More

MagVent Made My Life So Easy...

Kevin Kelley

“When we moved into our new home, one of the tasks I dreaded the most was installing my dryer. I had seen a couple of YouTube videos, and was curious about MagVent. I mentioned my curiosity to my brother-in-law who immediately began to rave about the MagVent he had recently purchased. So I took the plunge.

The moment I opened the box I was holding the best built dryer vent I had ever held. It felt so sturdy. I looked at the space I had to work with at home, and immediately felt confident I could knock this out with my handy new sidekick. MagVent made installation a breeze. I have included pictures of the before and after. I walked away feeling like a pro. Thanks for this product. It made my life so easy.” -Scott T.

Read More

MagVent Solved the Problem

Kevin Kelley

“Our dryer has a side vent and the distance between the dryer and the wall is only 7 inches, making conventional taping very difficult. The dryer door requires a firm closing and that sometimes caused the light weight dryer to move on the hard floor. Even slight movement would cause the dryer to disconnect from the vent. I decided to use MagVent and that solved the problem. Now even slight movement can be accommodated by the MagVent.” -Chuck R.

Read More

A Happy Customer Gives Thanks to MagVent!

Kevin Kelley

"Hi, my name is Jeremy Armagost. I am happy to tell you my story.
I had just moved into a new place and attempted to hook up my dryer. The space was tight and I needed a fair amount of foil duct. As I slid the dryer into place, the foil coiled, creating crooks and bends. The dryer began to overheat and needed to be pulled out each time. There had to be a better way. Then, I stumbled upon MagVent! After watching the videos, the solution was simple. I had to have one. This is easily the best money spent. Every penny. Everything I needed arrived quickly. In my case, I was lucky and needed only a flat screwdriver to install. In no time, my dryer was back in place, running cool. Thanks MagVent!"

Read More